|
Document
Number |
Title |
|
ISO 7637-1 |
Road vehicles --
Electrical disturbances from
conduction and coupling -- Part 1:
Definitions and general
considerations |
|
ISO 7637-2 |
Road vehicles --
Electrical disturbances from
conduction and coupling -- Part 2:
Electrical transient conduction
along supply lines only |
|
ISO 7637-3 |
Road vehicles --
Electrical disturbance by conduction
and coupling -- Part 3: Vehicles
with nominal 12 V or 24 V supply
voltage -- Electrical transient
transmission by capacitive and
inductive coupling via lines other
than supply lines |
|
ISO/TR 10305-1 |
Road vehicles --
Calibration of electromagnetic field
strength measuring devices -- Part
1: Devices for measurement of
electromagnetic fields at
frequencies > 0 Hz |
|
ISO/TR 10305-2 |
Road vehicles --
Calibration of electromagnetic field
strength measuring devices -- Part
2: IEEE standard for calibration of
electromagnetic field sensors and
probes, excluding antennas, from 9
kHz to 40 GHz |
ISO 10605 |
Road vehicles -- Test methods for electrical disturbances from electrostatic discharge |
|
ISO/TS 14907-1 |
Road transport and
traffic telematics -- Electronic fee
collection -- Test procedures for
user and fixed equipment -- Part 1:
Description of test procedures |
|
ISO/TS 14907-2 |
Road transport and
traffic telematics -- Electronic fee
collection -- Test procedures for
user and fixed equipment -- Part 2:
Conformance test for the onboard
unit application interface |
|
ISO/TS 21609 |
Road vehicles --
(EMC) guidelines for installation of
aftermarket radio frequency
transmitting equipment |
|
ISO 11451-1 |
Road vehicles --
Vehicle test methods for electrical
disturbances from narrowband
radiated electromagnetic energy --
Part 1: General principles and
terminology |
|
ISO 11451-2 |
Road vehicles --
Vehicle test methods for electrical
disturbances from narrowband
radiated electromagnetic energy --
Part 2: Off-vehicle radiation
sources |
|
ISO 11451-3 |
Road vehicles --
Electrical disturbances by
narrowband radiated electromagnetic
energy -- Vehicle test methods --
Part 3: On-board transmitter
simulation |
|
ISO 11451-4 |
Road vehicles --
Vehicle test methods for electrical
disturbances from narrowband
radiated electromagnetic energy --
Part 4: Bulk current injection
(BCI) |
|
ISO 11452-1 |
Road vehicles --
Component test methods for
electrical disturbances from
narrowband radiated electromagnetic
energy -- Part 1: General principles
and terminology |
|
ISO 11452-2 |
Road vehicles --
Component test methods for
electrical disturbances from
narrowband radiated electromagnetic
energy -- Part 2: Absorber-lined
shielded enclosure |
|
ISO 11452-3 |
Road vehicles --
Component test methods for
electrical disturbances from
narrowband radiated electromagnetic
energy -- Part 3: Transverse
electromagnetic mode (TEM) cell |
|
ISO 11452-4 |
Road vehicles --
Component test methods for
electrical disturbances from
narrowband radiated electromagnetic
energy -- Part 4: Bulk current
injection (BCI) |
|
ISO 11452-5 |
Road vehicles --
Component test methods for
electrical disturbances from
narrowband radiated electromagnetic
energy -- Part 5: Stripline |
|
ISO 11452-7 |
Road vehicles --
Component test methods for
electrical disturbances from
narrowband radiated electromagnetic
energy -- Part 7: Direct radio
frequency (RF) power injection |
ISO 11452-8 |
Road vehicles --
Component test methods for
electrical disturbances from
narrowband radiated electromagnetic
energy -- Part 8: Immunity to magnetic fields |
|
ISO 13766 |
Earth-moving
machinery -- Electromagnetic
compatibility |
|
Document
Number |
Title |
|
J1113/1 |
Electromagnetic
Compatibility Measurement Procedures
and Limits for Components of
Vehicles, Boats (Up to 15 M), and
Machines (Except Aircraft) (50 Hz to
18 Ghz) |
|
J1113/2 |
Electromagnetic
Compatibility Measurement Procedures
and Limits for Vehicle Components
(Except Aircraft)--Conducted
Immunity, 15 Hz to 250 kHz--All
Leads |
|
J1113/3 |
Conducted Immunity,
250 kHz to 400 MHz, Direct Injection
of Radio Frequency (RF) Power |
|
J1113/4 |
Immunity to Radiated
Electromagnetic Fields-Bulk Current
Injection (BCI) Method |
|
J1113/11 |
Immunity to Conducted
Transients on Power Leads |
|
J1113/12 |
Electrical
Interference by Conduction and
Coupling - Capacitive and Inductive
Coupling via Lines Other than Supply
Lines |
|
J1113/13 |
Electromagnetic
Compatibility Measurement Procedure
for Vehicle Components - Part 13:
Immunity to Electrostatic
Discharge |
|
J1113/21 |
Electromagnetic
Compatibility Measurement Procedure
for Vehicle Components - Part 21:
Immunity to Electromagnetic Fields,
30 MHz to 18 GHz, Absorber-Lined
Chamber |
J1113/24 |
Immunity to Radiated Electromagnetic Fields; 10 kHz to
200 MHz--Crawford TEM Cell and 10 kHz to 5 GHz--Wideband TEM Cell |
|
J1113/26 |
Electromagnetic
Compatibility Measurement Procedure
for Vehicle Components - Immunity to
AC Power Line Electric Fields |
|
J1113/27 |
Electromagnetic
Compatibility Measurements Procedure
for Vehicle Components - Part 27:
Immunity to Radiated Electromagnetic
Fields - Mode Stir Reverberation
Method |
|
J1113/28 |
Electromagnetic
Compatibility Measurements Procedure
for Vehicle Components--Part
28--Immunity to Radiated
Electromagnetic
Fields--Reverberation Method (Mode
Tuning) |
|
J1113/42 |
Electromagnetic
Compatibility--Component Test
Procedure--Part 42--Conducted
Transient Emissions |
|
J1752/1 |
Electromagnetic
Compatibility Measurement Procedures
for Integrated Circuits-Integrated
Circuit EMC Measurement
Procedures-General and
Definition |
|
J1752/2 |
Measurement of
Radiated Emissions from Integrated
Circuits -- Surface Scan Method
(Loop Probe Method) 10 MHz to 3
GHz |
|
J1752/3 |
Measurement of
Radiated Emissions from Integrated
Circuits -- TEM/Wideband TEM (GTEM)
Cell Method; TEM Cell (150 kHz to 1
GHz), Wideband TEM Cell (150 kHz to
8 GHz) |
|
J551/5 |
Performance Levels
and Methods of Measurement of
Magnetic and Electric Field Strength
from Electric Vehicles, Broadband, 9
kHz To 30 MHz |
|
J551/11 |
Vehicle
Electromagnetic
Immunity--Off-Vehicle Source |
|
J551/12 |
Vehicle
Electromagnetic Immunity--On-Board
Transmitter Simulation |
|
J551/13 |
Vehicle
Electromagnetic Immunity--Bulk
Current Injection |
|
J551/15 |
Vehicle
Electromagnetic
Immunity--Electrostatic Discharge
(ESD) |
|
J551/16 |
Electromagnetic
Immunity - Off-Vehicle Source
(Reverberation Chamber Method) -
Part 16 - Immunity to Radiated
Electromagnetic Fields |
|
J551/17 |
Vehicle
Electromagnetic Immunity -- Power
Line Magnetic Fields |
|
J1812 |
Function Performance
Status Classification for EMC
Immunity Testing |
|
J2628 |
Characterization--Conducted
Immunity |
|
J2556 |
Radiated Emissions
(RE) Narrowband Data Analysis--Power
Spectral Density (PSD) |
Audi TL 82466 |
Electrostatic Discharge |
BMW 600 13.0 |
Electric- / Electronic components in cars |
BMW GS 95002 |
Electromagnetic
Compatibility (EMC) Requirements and
Tests |
BMW GS 95003-2 |
Electric- / Electronic assemblies in motor vehicles |
Chrysler PF 9326 |
Electrical electronic modules and motors |
FIAT 9.90110 |
Electric and electronic devices for motor vehicles |
Freightliner 49-00085 |
EMC requirements |
Honda 3838Z-S5AA-L000 |
Noise Simulation Test |
Honda 3982Z-SDA-0030 |
|
Hyundai ES 39110-00 |
EMC requirements |
Hyundai ES 96100-01 |
|
IVECO 16-2103 |
EMC requirements |
Kia/Hyundai ES-95400-10 |
|
Lotus 17.39.01 |
Lotus Engineering Standard: Electromagnetic Compatibility |
Mack Trucks 606GS15 |
EMC requirements |
MAN 3285 |
EMC requirements |
Mazda MES PW 67600 |
Automobile parts standard (electronic devices) |
Mercedes A 211 000 42 99 |
Instruction specification of test method for E/E-components |
Mercedes AV EMV |
Electric aggregate and electronics in cars |
Mercedes MBN 10284-2 |
EMC requirements and tests of E/E-systems (component test procedures) |
Mercedes MBN 22100-2 |
Electric / electronic elements, devices in trucks |
Mitsubishi ES-X82010 |
General specification of environment tests on automotive electronic equipment |
Nissan 28400 NDS03 |
Low frequency surge resistance of electronic parts |
Nissan 28400 NDS07 |
Immunity against low frequency surge (induction surge) of electronic parts |
Nissan 28401 NDS02 |
EMC requirements (instruction concerning vehicle and electrical, electronic and pyrotechnic equipment) |
Porsche AV EMC EN |
EMC requirements |
PSA B21 7090 |
EMC requirements (electric and electronics equipment) |
PSA B21 7110 |
EMC requirements (electric and electronics equipment) |
Renault 36.00.400 |
Physical environment of electrical and electronic equipments |
Renault 36.00.808 |
EMC requirements (cars and electrical / electronic components) |
Scania TB1400 |
EMC requirements |
Scania TB1700 |
|
Smart DE10005B |
EMC requirements (electric aggregate and electronics in cars) |
Toyota TSC3500G |
Engineering standard (analog read-out meter) |
Toyota TSC3590G |
Engineering standard (clock) |
Toyota TSC7001G |
Engineering standard (electric noise of electronic devices) |
Toyota TSC7203G |
Engineering standard (ABS-TRC computers) |
Toyota TXC7315G |
Electrostatic Discharge (Gap Method) |
Visteon ES-XU3F-1316-AA |
|
Volvo EMC Requirements |
EMC requirements for 12V and 24V systems |
Volkswagen VW TL 801 01 |
Electric and electronic components in cars |
Volkswagen VW TL 820 66 |
Conducted
Interference |
Volkswagen VW TL 821 66 |
EMC requirements of electronic components - bulk current injection (BCI) |
Volkswagen VW TL 823 66 |
Coupled Interference
on Sensor Cables |
Volkswagen VW TL 824 66 |
Immunity Against
Electrostatic Discharge |
Volkswagen VW TL 965 |
Short-Distance Interference Suppression |
